Logic PSU with Overvoltage Protection

-

Description:
A simple 5 Volt regulated PSU featuring overvoltage protection.


Notes
The 5 volt regulated power supply for TTL and 74LS series integrated circuits, has to be very precise and tolerant of voltage transients. These IC's are easily damaged by short voltage spikes. A fuse will blow when its current rating is exceeded, but requires several hundred milliseconds to respond. This circuit will react in a few microseconds, triggered when the output voltage exceeds the limit of the zener diode.

This circuit uses the crowbar method, where a thyristor is employed and short circuits the supply, causing the fuse to blow. This will take place in a few microseconds or less, and so offers much greater protection than an ordinary fuse. If the output voltage exceed 5.6Volt, then the zener diode will conduct, switching on the thyristor (all in a few microseconds), the output voltage is therefore reduced to 0 volts and sensitive logic IC's will be saved. The fuse will still take a few hundred milliseconds to blow but this is not important now because the supply to the circuit is already at zero volts and no damage can be done. The dc input to the regulator needs to be a few volts higher than the regulator voltage. In the case of a 5v regulator, I would recommend a transformer with secondary voltage of 8-10volts ac.

By choosing a different regulator and zener diode, you can build an over voltag trip at any value. I have a simulated transient graph of this over voltage protection circuit in the Design section

Circuit Modification
I have a circuit modification from one of my viewers in Sweden, Ulf Kylenfall. The modified circuit is shown below and the electrolytic capacitor is moved to a position directly after the rectifier bridge and before the fuse.


With the original circuit, the thyristor had to [rapidly] discharge the capacitor in its effort to protect the downstream circuitry. This current surge may otherwise destroy the thyristor depending on what quality that has been used for the capacitor.

With the modified circuit, shown above, the fuse needs to blow in such a short time that the integrated energy dissipation over the thyristor is within its limits. Moving the capacitor to a position before the fuse ensures this. (Provided that a sufficiently fast-blow fuse has been used).



Thank you Ulf, for highlighting this design problem, and your solution to improve the circuit, kind regards Andy Collinson.

Popular posts from this blog

12 Volt 30 Amp Power Supply

-
Image
Using a single 7812 IC voltage regulator and multiple outboard pass transistors, this power supply can deliver output load currents of up to 30 amps. The design is shown below: Notes The input transformer is likely to be the most expensive part of the entire project. As an alternative, a couple of 12 Volt car batteries could be used. The input voltage to the regulator must be at least several volts higher than the output voltage (12V) so that the regulator can maintain its output. If a transformer is used, then the rectifier diodes must be capable of passing a very high peak forward current, typically 100amps or more. The 7812 IC will only pass 1 amp or less of the output current, the remainder being supplied by the outboard pass transistors. As the circuit is designed to handle loads of up to 30 amps, then six TIP2955 are wired in parallel to meet this demand. The dissipation in each power transistor is one sixth of the total load, but adequate heat sinking is still require
Read more

A 13.8V 20A PSU

-
Image
Regulated DC power supply Notes This PSU has been especially designed for current-hungry ham radio transceivers. It delivers safely around 20Amps at 13.8V. For lower currents, a separate current limiting output, capable of 15ma up to a total of 20A has been added. The power transformer should be capable to deliver at least 25A at 17.5 to 20V. The lower the voltage, the lower power dissipation. The rectified current will be "ironed" by C1, whose capacity should not be less than 40.000uF, (a golden rule of around 2000uF/A), but we recommend 50.000uF. This capacity can be built up by several smaller capacitors in parallel. The base of this design is a simple 12V regulator (7812). The output voltage can be brought to desired value (here 13.8V) by two external resistors (R5 and R6) using this formula: U= 12(1+R5/R6) The low currents (here 15mA) will keep the 7812 in its regular function. As soon as the current rises over 15ma, the voltage drop on R4 will "o
Read more

1.2 - 15V/3A adjustable regulated power supply

-
Image
Specifications This kit provides a variable output power supply ranging from 1.2 to 15 V @ 3 A. It uses Low Dropout Positive Regulator LM1084 in TO220 package for delivering variable output voltage. Input - 18 VAC/DC Output - variable output from 1.2 ~ 15 V @ 3 A Regulated low ripple DC voltage Heatsink for regulator IC On board bridge rectifier to convert AC to DC LED indication at input of IC Zener trimmed band gap reference, current limiting and thermal shutdown (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Onboard PCB mounted Potentiometer (POT) for varying the output voltage Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 58 mm Schematic Parts List PCB
Read more