Overvoltage Protection for the LM317

-

Description
This is an add-on Over Voltage Circuit for the LM317 Regulator Circuit subhttp://www.blogger.com/img/blank.gifmitted by Matthew Hewson. The original circuit may be viewed here.



Notes
It is a voltage regulator that allows a 6v portable supply to be derived from the 12v car battery. You can add a 6.2V zener diode and a LED to warn you when the input supply is overvoltage. If you could find a relay that would operate from 6.2v right up to 12v that you could connect in such a way that if over voltage occurred, then the relay would automatically switch off the output preventing damage to any connected equipment.
Such a relay would be quite difficult to find, so I designed this, it is a simple two transistor circuit which will switch off the output should the voltage raise above 6.2v (this can be changed by selecting a different value of zener diode ).

Components are as follows:
ZD1 =3D 6.2v Zener diode (you can change this to any value, the circuit will switch off the output if the input voltage raises above the value of the zener diode)
R1 = 1K Resistor (this can be of any power rating, it carries very little power)
R2 = 1K Resistor (this can be of any power rating, it carries very little power)
T1 = Low power NPN Transistor (BC108 or BC547 will do fine)
T2 = NPN transistor transistor capable of switching the equipment you are running (BFY51 or BC140 can switch 1 Amp, which is the maximum the voltage regulator circuit can handle)

It is advisable to test this circuit with a voltmeter, slowly increasing the voltage on the regulator circuit and make sure that this circuit switches off the output when the value of the zener diode is reached, before plugging in your expensive equipment. This circuit is intended to be used with the voltage regulator posted by Matthew Hewson, my overvolatge add-on circuit is shown with the original below:-


Double check the polarity, It is very easy to blow up components in the eqipment that you are powering if you reverse the polarity. Also, if you want to increase the power output of the voltage regulator circuit above 1 Amp then connect several LM317's in parallel, be sure to make sure that transistor T2 on this circuit is of a high enough rating if you do this.
If you have any problems with this circuit, you can email me at: electronicplanetuk@hotmail.com
or have a look for updates on my http://www.electronics.vze.com/
Adam

Popular posts from this blog

12 Volt 30 Amp Power Supply

-
Image
Using a single 7812 IC voltage regulator and multiple outboard pass transistors, this power supply can deliver output load currents of up to 30 amps. The design is shown below: Notes The input transformer is likely to be the most expensive part of the entire project. As an alternative, a couple of 12 Volt car batteries could be used. The input voltage to the regulator must be at least several volts higher than the output voltage (12V) so that the regulator can maintain its output. If a transformer is used, then the rectifier diodes must be capable of passing a very high peak forward current, typically 100amps or more. The 7812 IC will only pass 1 amp or less of the output current, the remainder being supplied by the outboard pass transistors. As the circuit is designed to handle loads of up to 30 amps, then six TIP2955 are wired in parallel to meet this demand. The dissipation in each power transistor is one sixth of the total load, but adequate heat sinking is still require
Read more

A 13.8V 20A PSU

-
Image
Regulated DC power supply Notes This PSU has been especially designed for current-hungry ham radio transceivers. It delivers safely around 20Amps at 13.8V. For lower currents, a separate current limiting output, capable of 15ma up to a total of 20A has been added. The power transformer should be capable to deliver at least 25A at 17.5 to 20V. The lower the voltage, the lower power dissipation. The rectified current will be "ironed" by C1, whose capacity should not be less than 40.000uF, (a golden rule of around 2000uF/A), but we recommend 50.000uF. This capacity can be built up by several smaller capacitors in parallel. The base of this design is a simple 12V regulator (7812). The output voltage can be brought to desired value (here 13.8V) by two external resistors (R5 and R6) using this formula: U= 12(1+R5/R6) The low currents (here 15mA) will keep the 7812 in its regular function. As soon as the current rises over 15ma, the voltage drop on R4 will "o
Read more

1.2 - 15V/3A adjustable regulated power supply

-
Image
Specifications This kit provides a variable output power supply ranging from 1.2 to 15 V @ 3 A. It uses Low Dropout Positive Regulator LM1084 in TO220 package for delivering variable output voltage. Input - 18 VAC/DC Output - variable output from 1.2 ~ 15 V @ 3 A Regulated low ripple DC voltage Heatsink for regulator IC On board bridge rectifier to convert AC to DC LED indication at input of IC Zener trimmed band gap reference, current limiting and thermal shutdown (provided by IC feature) Power Battery Terminal (PBT) for easy input and output connection Onboard PCB mounted Potentiometer (POT) for varying the output voltage Filter capacitors for low ripple DC output Four mounting holes of 3.2 mm each PCB dimensions 46 mm x 58 mm Schematic Parts List PCB
Read more